Wholly flexible, prefabricated pipe insulation manufactured from elastomeric rubber foam material in the form of pipes, for use on piping installations on cold and warm lines.
The ODE R-FLEX Pipe is offered in to three groups,DIAMOND, PRM (Premium) and STD (Standard).
It is manufactured unfaced or with various types of facing with diameters of 6 mm 114 mm and thicknesses of 6 mm - 40 mm.
LAMINATED PRODUCTS:
ODE R-FLEX ALUGLASS PIPE
ODE R-FLEX AL-CLAD PIPE
ODE R-FLEX ALU PIPE
It is covered with aluminum facing with a thickness of 54 micron.
ODE R-FLEX METALIZED PIPE
Lenght (mm) | Thickness (mm) | ||||||
6 | 9 | 13 | 19 | 25 | 32 | 40 | |
2000 | √ | √ | √ | √ | √ | √ | √ |
ODE R-FLEX DIAMOND PIPE
Name of Product | λ (Thermal Conductivity) W/ (m.K) | µ (Water Vapor Diffusion Resistance Factor) | Fire Response Classification (EN 13501-1) |
R-FLEX DIAMOND Pipe | 0.034 (0 °C) | 11000 | BL-s2,d0 |
0.039 (25 °C) | |||
0.041 (75 °C) |
ODE R-FLEX PRM PIPE
Name of Product | λ (Thermal Conductivity) W/ (m.K) | µ (Water Vapor Diffusion Resistance Factor) | Fire Response Classification (EN 13501-1) |
R-FLEX PRM Pipe | 0.034 (0 °C) | 7000 | BL-s2,d0 |
0.039 (25 °C) | |||
0.041 (75 °C) |
ODE R-FLEX STD PIPE
Name of Product | λ (Thermal Conductivity) W/ (m.K) | µ (Water Vapor Diffusion Resistance Factor) | Fire Response Classification (EN 13501-1) |
R-FLEX STD Pipe | 0.036 (0 °C) | 5000 | BL-s3,d0 |
0.039 (25 °C) | |||
0.041 (75 °C) |
ODE KONFiX (ODE R-FLEX ADHESIVE)
Synthetic rubber based super-strong adhesive used in ODE R-flex applications. Prevents convection currents at joints, facilitates easy and fast installation. Surfaces to which the product shall be applied should not be greasy or dusty, and ODE Konfix should be applied by using a roll, brush, or spray gun equally on both surfaces, and adhesion should be ensured under constant pressure. The drying period varies between 10 seconds and 4 minutes, and the time required for complete adhesion is 24 hours.
Adhesive | Quantity (kg) |
ODE KONFIX 14/1 | 14 |
ODE KONFIX 3/1 | 3 |
ODE KONFIX 14/1 | 14 |
ODE KONFIX 3/1 | 3 |
APPLICATION INFORMATION
![]() ![]() ![]() ![]() ![]() | 1. If pipework has already been installed, cut the ODE R-Flex Pipe lengthwise. Use only sharp blades for cutting. This will make it easier for you to apply the adhesive. |
![]() ![]() | 2. Place the Ode R-Flex pipe around the pipe that is to be insulated, and apply Ode R-Flex Adhesive on the edges on the end section as well as the edges that have been formed along the slit. |
![]() | 3. Once you are sure the adhesive is dry, gently press both edges of the slit together, sticking them together. |
![]() | 4. Cut a part a few mmlonger than required tocover the region betweentwo insulating pipes. If the piece you cut is not long enough, it will make the insulation properties in the area worse. |
![]() | 5. Cut a piece that is a few mm longer than is needed to cover the seam between two insulation pipes. If the piece you have cut is not long enough, the insulating properties in this area will suffer. |